Engineering notes

Measured, not marketed.

Numbers are easy to print. We publish the method behind them: what we measure, on which rig, and what happens when a batch misses.

On this page

01 / Optics

The filament is the fixture.

A reflector or projector is designed around one precise light source — the halogen filament. Move that source two millimetres and the beam moves with it, straight into oncoming traffic.

  • Emitting surfaces are aligned to the halogen filament within ±0.15 mm in all three axes.
  • Freeform projector lenses are polished for a cut-off sharpness of 0.7° at 10 m.
  • Beam patterns are verified on a calibrated 10 m wall for every production batch.
10 m WALL / LOW BEAM CUT-OFF 0.7° 0 lx ISO 8624
FIG. 01 1:1 position The chip sits where the filament sat — no spacer, no tilt, no guesswork.

02 / Thermal

Thirty percent more heat, moved.

Lumens fall when the junction runs hot. Instead of a bigger heatsink, we shorten the path between chip and air.

  • Sintered copper heat pipes carry heat from the PCB to a fin stack 30% larger in surface area.
  • A 12,000 rpm fluid-dynamic bearing fan holds junction temperature at 105 °C in a 40 °C ambient.
  • Output after 1,000 hours is 96% of initial lumens — measured, not estimated.

Junction temperature under load

Competitor bulb
118 °C
HWKAD VX-25
105 °C
060120 °C

Continuous operation, 40 °C ambient, 6,000 rpm airflow.

FIG. 02 Junction temperature under load

03 / Electronics

Quiet current for noisy cars.

Modern vehicles watch their lamps. A driver that draws a clean, predictable current is the difference between a silent install and a dashboard full of warnings.

  • 9–32 V input with reverse-polarity, load-dump and over-temperature protection.
  • CANbus-stable on more than 98% of tested platforms; decoder harness supplied where needed.
  • Conducted and radiated EMI filtered to CISPR 25 Class 5 for DRL, radio and camera systems.

Driver signal

01 Supply
02 Filter
03 Constant current
04 LED

PWM above 3 kHz, invisible to cameras and the human eye.

FIG. 03 Driver signal

04 / Validation

Eight tests. Then a batch.

Every new SKU passes the same protocol before release. Production batches repeat the short form on a 2% sample.

01 Aging 1,200 hours at 85 °C / 85% RH
02 Thermal shock −40 ↔ +105 °C, 200 cycles
03 Immersion IP68, 1 m for 24 hours
04 Vibration 30 G, 10–2,000 Hz, 8 hours
05 Voltage 9–32 V, load dump 87 V
06 Photometry Beam pattern on a 10 m wall
07 Salt spray 480 hours, ASTM B117
08 Lumen maintenance LM-80 style, 6,000 hours
2%Batch sample size
0.4%Field failure rate
96%Lumens at 1,000 h
38Markets shipped

FAQ

Questions, answered.

If your question isn't here, an engineer will answer it directly.

Ask an engineer
01Are HWKAD bulbs legal on public roads?

It depends on your country and housing. Our road-legal ranges carry ECE R112 E-marks; competition and off-road products do not. Tell us your market and we will send the exact list of approved SKUs.

02Will I get a CANbus error or flicker?

The VX, XD and MX drivers are CANbus-stable on more than 98% of tested platforms. For sensitive vehicles we include a decoder harness at no extra cost.

03Do I need an external driver?

Not for MX, XD, SP or SG — the driver is integrated. VX and PL use a compact inline driver that fits inside most housings.

04What does the warranty cover?

Three years against manufacturing defects, with batch-level traceability. Field failure rate is below 0.4%.

05Can you produce our own brand?

Yes. OEM and ODM from 100 sets per SKU: custom PCB, laser marking, retail packaging and multi-language manuals.

06How fast can I get samples?

Stock samples ship within 48 hours. Custom samples take 7–10 working days, including the photometric report.

Lab access

Want the full test report?

We share photometric reports, thermal curves and E-mark certificates for any SKU under NDA.